Modelling the effect of changing precipitation inputs on deep soil water utilization          下载免费PDF全文

Ji Qi  Daniel Markewitz  David Radcliffe 《水文研究》2018,32(5):672-686

Forests in the Southeastern United States are predicted to experience future changes in seasonal patterns of precipitation inputs as well as more variable precipitation events. These climate change‐induced alterations could increase drought and lower soil water availability. Drought could alter rooting patterns and increase the importance of deep roots that access subsurface water resources. To address plant response to drought in both deep rooting and soil water utilization as well as soil drainage, we utilize a throughfall reduction experiment in a loblolly pine plantation of the Southeastern United States to calibrate and validate a hydrological model. The model was accurately calibrated against field measured soil moisture data under ambient rainfall and validated using 30% throughfall reduction data. Using this model, we then tested these scenarios: (a) evenly reduced precipitation; (b) less precipitation in summer, more in winter; (c) same total amount of precipitation with less frequent but heavier storms; and (d) shallower rooting depth under the above 3 scenarios. When less precipitation was received, drainage decreased proportionally much faster than evapotranspiration implying plants will acquire water first to the detriment of drainage. When precipitation was reduced by more than 30%, plants relied on stored soil water to satisfy evapotranspiration suggesting 30% may be a threshold that if sustained over the long term would deplete plant available soil water. Under the third scenario, evapotranspiration and drainage decreased, whereas surface run‐off increased. Changes in root biomass measured before and 4 years after the throughfall reduction experiment were not detected among treatments. Model simulations, however, indicated gains in evapotranspiration with deeper roots under evenly reduced precipitation and seasonal precipitation redistribution scenarios but not when precipitation frequency was adjusted. Deep soil and deep rooting can provide an important buffer capacity when precipitation alone cannot satisfy the evapotranspirational demand of forests. How this buffering capacity will persist in the face of changing precipitation inputs, however, will depend less on seasonal redistribution than on the magnitude of reductions and changes in rainfall frequency.  相似文献   

基于ROMS和4DVAR的沿轨与网格化SSH数据同化效果评价   总被引：1，自引：1，他引：0  

周超杰  丁效华  张杰  杨俊刚  马强 《海洋学报(英文版)》2018,37(9):50-58

Remote sensing products are significant in the data assimilation of an ocean model. Considering the resolution and space coverage of different remote sensing data, two types of sea surface height(SSH) product are employed in the assimilation, including the gridded products from AVISO and the original along-track observations used in the generation. To explore their impact on the assimilation results, an experiment focus on the South China Sea(SCS) is conducted based on the Regional Ocean Modeling System(ROMS) and the four-dimensional variational data assimilation(4 DVAR) technology. The comparison with EN4 data set and Argo profile indicates that, the along-track SSH assimilation result presents to be more accurate than the gridded SSH assimilation, because some noises may have been introduced in the merging process. Moreover, the mesoscale eddy detection capability of the assimilation results is analyzed by a vector geometry–based algorithm. It is verified that, the assimilation of the gridded SSH shows superiority in describing the eddy's characteristics, since the complete structure of the ocean surface has been reconstructed by the original data merging.  相似文献   

Three-dimensional finite element simulation of fracture propagation in rock specimens with pre-existing fissure(s) under compression and their strength analysis     

Ramin Pakzad  Shanyong Wang  Scott W. Sloan 《国际地质力学数值与分析法杂志》2020,44(10):1472-1494

A FORTRAN program, consistent with the commercially available finite element (FE) code ABAQUS, is developed based on a three-dimensional (3D) linear elastic brittle damage constitutive model with two damage criteria. To consider the heterogeneity of rock, the developed FORTRAN program is used to set the stiffness and strength properties of each element of the FE model following a Weibull distribution function. The reliability of the program is assessed against available experimental results for granite cylindrical specimens with a throughgoing, flat and inclined fissure. The calibration procedure of the material parameters is explained in detail, and it is shown that the compressive to tensile strength ratio can have a substantial influence on the failure response of the specimens. Numerical simulations are conducted for models with different levels of heterogeneity. The results show a smaller load bearing capacity for models with less homogeneity, representing gradual coalescence of fully damaged elements forming throughout the models during loading. The maximum load bearing capacity is studied for various combinations of inclination angles of two centrally aligned, throughgoing and flat fissures of equal length embedded in cylindrical models under uniaxial and multiaxial loading conditions. The key role of the compressive to tensile strength ratio is highlighted by repeating certain simulations with a lower compressive to tensile strength ratio. It is proven that the peak loads of the rock models with sufficiently small compressive to tensile strength ratios containing two throughgoing fissures of equal length are similar, provided that the minimum inclination angles of the models are the same. The results are presented and discussed with respect to the existing experimental findings in the literature, suggesting that the numerical model applied in this study can provide useful insight into the failure behaviour of rock-like materials.  相似文献   

Implementation of a coupled plastic damage distinct lattice spring model for dynamic crack propagation in geomaterials          下载免费PDF全文

Chao Jiang  Gao‐Feng Zhao 《国际地质力学数值与分析法杂志》2018,42(4):674-693

This paper studies dynamic crack propagation by employing the distinct lattice spring model (DLSM) and 3‐dimensional (3D) printing technique. A damage‐plasticity model was developed and implemented in a 2D DLSM. Applicability of the damage‐plasticity DLSM was verified against analytical elastic solutions and experimental results for crack propagation. As a physical analogy, dynamic fracturing tests were conducted on 3D printed specimens using the split Hopkinson pressure bar. The dynamic stress intensity factors were recorded, and crack paths were captured by a high‐speed camera. A parametric study was conducted to find the influences of the parameters on cracking behaviors, including initial and peak fracture toughness, crack speed, and crack patterns. Finally, selection of parameters for the damage‐plasticity model was determined through the comparison of numerical predictions and the experimentally observed cracking features.  相似文献   

铜藻(Sargassum horneri)在营养限制胁迫后对NH₄-N的超补偿吸收研究     

李大鹏  马增岭  李慧  丁刚  辛美丽  吴海一  郭文 《海洋与湖沼》2018,49(4):904-909

以经济马尾藻铜藻(Sargassum horneri)为研究材料,研究了其在营养限制胁迫后对NH_4-N的超补偿吸收情况。实验分营养限制和恢复营养两个阶段进行,每个阶段均设置饥饿处理组、饱和处理组和正常对照组。铜藻在低营养限制胁迫(饥饿)下培养10天后,恢复营养盐培养3天,分别采用次溴酸盐氧化法和锌镉还原法测定培养液中的NH_4-N和NO_3-N的浓度。本文研究发现,饥饿处理组中铜藻吸收氨氮的速率远高于正常对照组和饱和处理组,在恢复培养第一天时,饥饿处理组对NH_4-N的吸收速率最高为14.94μmol/(g·h),与正常对照组及饱和处理组间差异显著。在恢复培养的后两天,三个处理组中铜藻对NH_4-N的吸收速率差异慢慢变小,直至最后几乎相同。三组对NO_3-N没有表现出较高的吸收,最高仅为6.15μmol/(g·h),结果表明:氮源包括NH_4-N和NO_3-N时,铜藻优先选择吸收NH_4-N。实验后称重测定生长速率:对照组、饥饿处理组和饱和组生长率(SGR)分别为8.48%、8.86%、8.01%,ANOVA方差分析表明,三者存在显著差异(P=0.0320.05),从而证实了铜藻也存在超补偿生长的现象。  相似文献   

Determination of subcatchment and watershed boundaries in a complex and highly urbanized landscape          下载免费PDF全文

Aimé Kayembe  Carl P. J. Mitchell 《水文研究》2018,32(18):2845-2855

Urban development significantly alters the landscape by introducing widespread impervious surfaces, which quickly convey surface run‐off to streams via stormwater sewer networks, resulting in “flashy” hydrological responses. Here, we present the inadequacies of using raster‐based digital elevation models and flow‐direction algorithms to delineate large and highly urbanized watersheds and propose an alternative approach that accounts for the influence of anthropogenically modified land cover. We use a semi‐automated approach that incorporates conventional drainage networks into overland flow paths and define the maximal run‐off contributing area. In this approach, stormwater pipes are clustered according to their slope attributes, which define flow direction. Land areas drained by each cluster and contributing (or exporting) flow to a topographically delineated catchment were determined. These land masses were subsequently added or removed from the catchment, modifying both the shape and the size. Our results in a highly urbanized Toronto, Canada, area watershed indicate a moderate net increase in the directly connected watershed area by 3% relative to a topographically forced method; however, differences across three smaller scale subcatchments are greater. Compared to topographic delineation, the directly connected watershed areas of both the upper and middle subcatchments decrease by 5% and 8%, respectively, whereas the lower subcatchment area increases by 15%. This is directly related to subsurface storm sewer pipes that cross topographic boundaries. When directly connected subcatchment area is plotted against total streamflow and flashiness indices using this method, the coefficients of variation are greater (0.93 to 0.97) compared to the use of digital elevation model‐derived subcatchment areas (0.78 to 0.85). The accurate identification of watershed and subcatchment boundaries should incorporate ancillary data such as stormwater sewer networks and retention basin drainage areas to reduce water budget errors in urban systems.  相似文献   

基于高斯两步移动搜寻法的村镇避难场所可达性研究     

但文羽  肖映辉  胡周灵  詹庆明 《地球信息科学学报》2018,20(10):1412-1421

避难场所可达性是指避难场所与受灾居民之间的通达性,即灾害发生时,避难人员通过避难疏散通道到达避难场所的难易程度,是评价避难场所布局合理性的重要指标。本研究结合高斯两步移动搜寻法和网络分析法,从供需双向出发对村镇地区避难场所进行可达性分析。2种方法的结合,既充分考虑了需求点与设施点的相互作用,又充分考虑了设施点的吸引力随距离的衰减关系,并基于实际道路,以步行疏散时间作为搜索半径,降低了传统研究中因忽略供需间相互作用及实际距离而引起的可达性结果的误差。最后,以神农架松柏镇区为例,验证该方法的实际应用价值。结果表明,该方法能够有效测定村镇地区避难场所的空间可达性,同时,基于GIS软件可以直观地揭示研究区域内避难场所可达性空间分布差异。该方法可为制定科学的村镇防灾减灾规划提供方法支持。  相似文献   

Properties of geogrid-reinforced marine slope due to the groundwater level changes     

Ramin Vali  Jie Li  Gholamreza Shams  Pieter van Gelder 《Marine Georesources & Geotechnology》2018,36(6):735-748

Evaluation of slope stability, especially in the absence of a proper bed such as marine soils, is one of the most important issues in geotechnical engineering. Using geogrid layers to enhance the strength and stability of embankments is regarded as a commendable stabilization method. On the other hand, groundwater level erratically fluctuates in coastal areas. Therefore, the aim of this research is to study the effects of groundwater level changes on stability of a geogrid-reinforced slope on loose marine soils in Qeshm Island, Iran. At first, geotechnical properties of the site were obtained by comprehensive series of geotechnical laboratory and in situ tests. Then, by simultaneous changes of groundwater level and several parameters such as embankment slope, loading, geogrid length, geogrid number, and tensile strength of geogrid, different characteristics such as embankment safety factor (SF), vertical and horizontal displacements at embankment top and embankment base were studied. It was observed that groundwater level had significant effects on behavior of the embankment. For most of the observations, by decreasing the groundwater level, the displacements decreased and consequently safety factor increased. Increasing the length, number, and tensile strength of geogrid led to the reduction of displacements and an increase in the safety factor.  相似文献   

基于圆柱多段拟合的隧道中轴线提取方法研究     

荆海峰  李广云  王力  杨文锋 《大地测量与地球动力学》2018,38(2):211-215

提出基于圆柱多段拟合的隧道中轴线提取方法。首先对隧道点云数据进行预处理，并将点云按隧道走向分成不同区段；然后对各区段依据轴线与表面点云法线垂直关系，提取精度较低的中轴线；最后对各区段利用圆柱多段拟合，提取精度较高的中轴线。实验表明，隧道中轴线的提取在一定的采样区间具有较高的稳定性，对直线和弯曲的圆形隧道有良好的适用性，算法可靠，精度较高。  相似文献   

基于GIS的石家庄市雾霾分析     

苏亚聪  史娟  徐爽 《北京测绘》2020,(2):233-237

为了得出雾霾气象成因机制、影响因素和时空分布特征,以石家庄市区与郊县为研究区域,将2013年9月至2016年12月石家庄市各市区、郊县的PM2.5历史监测数据中的有效数据进行了数据分析处理得到雾霾浓度数据,还有温度、降水、风速、地形和人口密度等数据,运用GIS分析的方法,模拟绘制石家庄雾霾的时空分布图、雾霾与各影响因子的专题对比图,得到雾霾形成机制的因子、雾霾的时空分布规律、雾霾季节变化特征、雾霾与地形间的关系等;运用数据分析软件OriginPro8.SR3分析雾霾浓度与风速数据、降雨数据、温度数据间的相关性。  相似文献